Multipass

| MicroK8s | VirtualBox|

Multipass

• https://multipass.run/

インスタンスの作成と開始

$ multipass launch --mem 8G --disk 40G --cpus 2 --name primary

ローカルドライブをマウント

• マウント

$ multipass mount $HOME/Workspaces/microk8s microk8s-vm:/home/ubuntu/manifest

• 確認

$ multipass info microk8s-vm
Name:           microk8s-vm
State:          Running
IPv4:           192.168.64.2
Release:        Ubuntu 18.04.5 LTS
Image hash:     a85c3190d0bb (Ubuntu 18.04 LTS)
Load:           0.79 0.95 1.02
Disk usage:     3.1G out of 48.3G
Memory usage:   1.0G out of 3.9G
Mounts:         /Users/hirotoyagi/Workspaces/microk8s => /home/ubuntu/manifest
                    UID map: 501:default
                    GID map: 20:default

• 解除

$ multipass unmount microk8s-vm

Tips

現在選択されているドライバを確認する

$ sudo multipass get local.driver
hyperkit

ドライバをVirualBoxに変更

• https://multipass.run/docs/using-virtualbox-in-multipass-macos

$ sudo multipass set local.driver=virtualbox
$ sudo VBoxManage list vms
Password:
"microk8s-vm" {d90718db-3795-4116-825f-cffe4a2f0fea}

• Bridge
  • https://www.virtualbox.org/manual/ch06.html#network_bridged

$ VBoxManage list bridgedifs | grep ^Name:
Name:            en0: Wi-Fi (AirPort)
Name:            en1: Thunderbolt 1
Name:            bridge0
Name:            p2p0
Name:            awdl0
Name:            llw0

$ sudo VBoxManage modifyvm microk8s-vm --nic2 bridged --bridgeadapter2 en0

• インスタンスを立ち上げて新しいNICの名前（enp0s8)を得る

$ multipass exec microk8s-vm ip link | grep DOWN
3: enp0s8:  mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000

• 新しいNIC（enp0s8)の設定

＄ multipass exec -- microk8s-vm sudo bash -c "cat > /etc/netplan/60-bridge.yaml" <<EOF
network:
  ethernets:
    enp0s8:                  # this is the interface name from above
      dhcp4: true
      dhcp4-overrides:       # this is needed so the default gateway
        route-metric: 200    # remains with the first interface
  version: 2
EOF

$ multipass exec microk8s-vm sudo netplan apply

$ multipass exec microk8s-vm ip address show dev enp0s8 up    
3: enp0s8: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000
    link/ether 08:00:27:3a:92:dd brd ff:ff:ff:ff:ff:ff
    inet 192.168.0.40/24 brd 192.168.0.255 scope global dynamic enp0s8
       valid_lft 86331sec preferred_lft 86331sec
    inet6 2402:6b00:3666:5800:a00:27ff:fe3a:92dd/64 scope global dynamic mngtmpaddr noprefixroute 
       valid_lft 266sec preferred_lft 266sec
    inet6 fe80::a00:27ff:fe3a:92dd/64 scope link 
       valid_lft forever preferred_lft forever

$ microk8s add-node
From the node you wish to join to this cluster, run the following:
microk8s join 10.0.2.15:25000/136ac2967078d5490de2d1a2d3a8bf52

If the node you are adding is not reachable through the default interface you can use one of the following:
 microk8s join 10.0.2.15:25000/136ac2967078d5490de2d1a2d3a8bf52
 microk8s join 192.168.0.40:25000/136ac2967078d5490de2d1a2d3a8bf52

Mac+Multipass+MicroK8s+Virtual Boxでネットワークブリッジを構成する

• Mac+Multipass+MicroK8s+Virtual Boxでネットワークブリッジを構成する